BUCKET TRUCK WIRELESS CONTROLLED PRODUCTS
EDRJW100 - Combo Wireless/Hard Wired Control System
- Up to 8 Wireless Inputs & Up to 8 Hard Wired Inputs
- Smart Engine Start/Stop - One Input Control
- Set RPM/E-Pump Control - One Input Control
- 3 Programable Set Speeds & Variable RPM Increase/Decrease
- Foot/Hand Throttle Control
- Auto Neutral
- Cab Throttle Inhibit
- On Board Programming
- LED Light Diagnosing
- Plug and Play Harnesses Available
TESS602 - 2 CHANNEL RECEIVER
This receiver has a four pin connector that is set up for power, ground and two momentary output channels. The TESS502 or 433T2 transmitters can be used with this product. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
TESS603 - TESS V2 WIRELESS RECEIVER 12 PIN
This receiver is used to control the engine start, engine stop, set RPM and emergency pump. You would use the following transmitters with this receiver, TESS504, 433T4 and 433T8. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
TESS604 - TESS V2 WIRELESS RECEIVER 10 PIN
This is a replacement for the previous TESS203/303 systems. It is the same size and has the same 10 Pin connector as the TESS203/303. It will controls the engines Starting and Stopping, set RPM and E-pump. It will not work with the previous TESS204 transmitter, you need to use either the TESS504, 433T4 or 433T8 transmitter. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
TESS502 - 2 BUTTON TRANSMITER
The TESS502 is used with the EDRJW series to control the engine start & stop with one button and the other button will control the engine set RPM and emergency pump. The range for the transmitter is roughly 1000' (300m). The unit operates from a single 3.6V 1/2 AA battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 4" X 4" X 2" enclosure.
TESS504 -4 BUTTON TRANSMITTER
The TESS504 is used to control 4 functions, Engine Start, Engine Stop, Set RPM and Emergency Pump. Mostly used in the Utility field for Bucket or Digger Derek trucks. The range for the transmitter is roughly 1000' (300m). The unit operates from a single 3.6V 1/2 AA battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 4" X 4" X 2" enclosure. Works with the TESS603 & TESS604 receiver.
433T2
This is a 2 Button FOB transmitter that is used with the EDRJW100. With this FOB you can Start the engine and stop the engine with one button, the other button will allow you to work the set RPM when the engine is running and when the engine is not running, it will allow you to turn on the E-Pump. This FOB will transmit up to 750 feet (230 m) and it measures 2.23" X 1.37" roughly.
433T4
This is a 4 Button FOB transmitter that can be used with the EDRJW100 & TESS604 receivers. This FOB has a function for each button. The four functions for this FOB are start the engine, stop the engine, controlling a set RPM and controlling the E-Pump. The line of sight range for this FOB is up to 750 feet (230 m) and it measures 2.23" X 1.37" roughly.
433T8
This is the hand held transmitter that will send up to 8 signals to the receiver. The label can be customized to show what each button that is used for. The range for the transmitter is roughly 1000' (300m). The body of the transmitter measures 2" high by 1.62" wide.